SKU: W2810S
Manufacturer: WireCrafters
A wire mesh security partition prevents pilferage, encloses work areas, and creates customized, accessible security areas in warehouses, manufacturing facilities, distribution centers, tool cribs, and other work areas. It gives you control of who has access to valuable inventory. The hardware is inaccessible from the exterior, so it can't be easily disassembled from outside the cage. Installation is fast because the design uses a minimum of parts. Panels install horizontally between 14-gauge tubular posts. The panels are steel wire woven into 2" x 1" rectangular mesh and securely welded to a 1-1/4" x 1-1/4" x 3/16" steel angle frame. Doors include cylinder key locks, other lock options are available.
Some assembly required on locking components and some accessories. Universal construction allows for left or right configuration of the door, with inside or outside slide.
Panels are constructed of 10 gauge (.135) steel wire, woven into 2" x 1" rectangular mesh and securely welded to a 1 1/4" x 1 1/4" x 1/8" steel angle frame. Frames have 7/8" x 7/16" slotted holes for mounting to posts and adjacent panels. Panels four to seven feet wide have one 1/4" x 3/4" stiffener welded to the frame. Wider panels have two stiffeners.
Posts are made of 2" x 2" x 14 gauge (.083) steel tubing. Base plates of 2" x 7" x 1/4" steel flat with two 7/16" round holes for floor anchoring, are welded to each. A decorative cap is tack welded to the top. Posts are drilled with 1/2" holes to accept hardware for mounting panels and doors. Hole spacing is set to leave a 3 1/4" sweep space below the panels. Posts have a 2" projection above the panels.
Doors are constructed of 10 gauge (.135) steel wire, woven into 2" x 1" rectangular mesh and securely welded to a 1 1/4" x 1 1/4" x 3/16" steel angle frame. Stiffeners, two horizontal and one vertical, of 1/4" x 3/4" steel flat are securely welded to the frame behind the mesh.
All erection hardware is supplied. Panel mounting hardware is 3/8" standard thread grade two plated fasteners. Floor anchors are 3/8" wedge type.
Nonplated parts receive one coat of gray acrylic enamel. Touch up paint is included with each order. Other colors are available.
Download Architectural Specifications:
Use one-sided partitions to enclose an area by anchoring it against two facing walls or building columns to create a secure wire wall. This partition can also be used at the end of rack rows or in other areas to create a single-wall barrier. This partition ships with posts at each end for panel connection, so it does not need to connect directly to facility walls.
Gate: The 4' wide wire mesh sliding gate extends to the full cage height. Enclosure ships with two doorposts, trolley trucks, key lock, 16-gauge tracks, and all hardware. The gate is constructed to work on the left or right hand side, inside or outside of the enclosure.
Footplates: Standard footplates are 2" x 7". They extend outside the post by 2½” per post position depending on footplate orientation. If you are in a seismic zone, or your floor is not smooth or even, a larger footplate may be required.
Partitions are designed to be anchored into a concrete floor. If your floor is uneven, or a surface that cannot hold anchors, contact us. Partitions can be installed on most any floor that can bear their weight, but there may be considerations with various floor surfaces. Contact us for assistance.
Finished in gray acrylic enamel. Available with gray powder coat finish upon request at no extra cost (may extend lead time). Other colors are also available in powder coat for an additional fee; contact us for more information.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and reproductive harm. For more information – www.p65warnings.ca.gov.
Lead Time: 1-2 weeks + transit time
Contact Cisco-Eagle to get a Shipping Rate for this item